AER Amp one Electric Bass Amplifier

Amp oneElectric Bass AmplifierThe amp one is an all-rounder, designed for the bassplayer who is used to switch between several styles and who sets value on weight, dimensions and easy operation. The 10-inch high performance bass-loudspeaker supports this versatility whilst simultaneously adding some tube-like compression. The design of the power-amp especially supports the impulse response and provides impressive power at short term, exceeding significantly the specified 200 W on 8 ohm, which you can clearly hear.Controls and Connections:Front side:input: Jack socket ¼“ (6.35 mm) high/low: High/low-switch: up= high, down= low gain: Input level control clip: Overload indicator mute: Channel mute switch colour: Switch for the tone colour: up= not active, down= active bass: Bass level conrol bass boost: Boosts the lower bass frequencies at 55 Hz middle: Middle level control freq.: Operating frequency of bass middle treble control bandwidth: Bandwidth the notch filter up= wide, down= narrow treble: Treble level controlTone balance:balance: Balance tone control, allows bass or treble accentuation or a combination of both intensity: Balance level controlCompressor:threshold: Control for compressor threshold ratio: Control for degree of compression Left stop: no compression Right stop: maximum compression active on/off: Switch to activate the compressorMaster:master: Master level control power: On/Off operation LEDRear side:gnd lift: Switch that disconnects signal ground from protective earth. Useful as remedy for hum loops. Generally, it should stay in the off position (not pushed in).headphones: Output for headphones. The loudspeaker of the amplifier is switched off when this socket is used. Caution: Please use only headphones with stereo (TRS) jack plug in this output socket. Connecting a mono plug may cause malfunction or damage.line out: Preamplifier output post master and tone controls, with effectssub out: Unfiltered / filtered output for an active / passive subwooferfootswitch: Connector for a dual footswitch Stereo jack socket, assignment: Tip = switch for internal effect Ring = switch for external effect (send / return)send: Output for an external, parallel effect loop in conjunction with return.return: Input of the external, parallel effect loop (see also send). Can also be used alone as additional input.insert pre/post eq: are two more effect loop paths to loop additional external effects (filter, compressor etc.) into the signal path, either pre or post equalization.aux in: Auxiliary input, 3.5 mm / 6.35 mm (stereo) jack socket, Stereo cinch (RCA) sockets (L/R) Additional input for general sources with line level, e.g. CD player. Mono or stereo jack plugs can be used. Also usable as mono input.tuner: Output for a tuner.aux level: Aux level controlpre/post: Switches the DI out pre or post the tone controlsDI level: DI level controlDI: Balanced XLR output, pre masterpower: Power on/off switch, combined with mains inlet (IEC C14 type) and compartment for mains fuse (see technical data).Technical specifications:Input: 6.3 mm (1/4”) input jack socket as high impedance line input stage with pad (high/low attenution).Equalizer: three band tone controls with middle parametricColour: ‘mid-cut-treble-boost’-filterTone balance: the tone balance enables the bass-or treble emphasis or a combination of both Effect: compressor with ratio and thresholdPower amp: 200 W / 8 ohms, dynamic controlAnalog signal processing: subsonic filter, low distortion RMS limiterSpeaker system: 10“ woofer neodymium magnetFeatures: ground lift, headphones, line out, sub out, footswitch (muting and effect loop), send, return, insert pre/post EQ, aux in, adjustable DI-outDimensions: 325mm x 375 mm x 295 mm (12.80“ x 14.80“ x 11.60“), HxWxDWeight: 14,1 kg (31,08 lbs)